N690 Steel Explained: Why Bohler's Mid-Range Stainless Still Makes Sense

The Steel Nobody Argues About

N690 does not get the attention of MagnaCut or M390, and it does not have the budget reputation of 8Cr13MoV. It just works. Bohler's cobalt-alloyed stainless has been a fixture in European knife making for decades, and it still shows up in everything from hunting knives to N690 folding knives because it hits a useful balance.

If you are shopping for a knife and see N690 on the spec sheet, here is what you are actually getting.

N690 sheepsfoot blade on the Trivisa Lamb-03B

What Is in N690

N690 is a stainless steel with roughly 1.07 percent carbon, 17 percent chromium, 1.5 percent cobalt, and small amounts of molybdenum and vanadium. The cobalt content is the distinguishing feature. It refines the grain structure during heat treatment, which improves edge stability and allows the steel to run at higher hardness without becoming brittle.

Typical hardness in production knives is 58-61 HRC. The Lamb-03B runs 60±2, which is right in the sweet spot.

How It Performs

  • Edge retention: better than 14C28N, noticeably behind M390 and MagnaCut. Expect a working edge for a couple of weeks of normal use.
  • Toughness: good. N690 resists chipping well at 60 HRC and tolerates thin grinds.
  • Corrosion resistance: very good. The 17 percent chromium and nitrogen content keep rust at bay in humid environments.
  • Sharpening: easy. Ceramic stones work fine, diamond is not required.

N690 vs 14C28N

This is the comparison most people actually need. 14C28N is tougher and slightly easier to sharpen. N690 holds an edge longer and has a bit more wear resistance. In daily use, the difference is subtle. If you cut a lot of abrasive material, N690 saves you sharpening time. If you are rough on edges, 14C28N survives more abuse.

N690 blade detail showing stonewash finish

Where N690 Shines

N690 is excellent in thin, slicey blades. Its grain structure supports a fine edge without crumbling, which is why European makers use it on hunting and fishing knives. It is also a good choice for anyone who wants a stainless blade that does not require diamond stones or a steep learning curve.

It is less ideal for heavy chopping or prying, where tougher carbon steels or 3V make more sense. But for a folding EDC knife, it is more than enough.

Care

Standard stainless care applies. Wipe it dry, keep it out of damp sheaths, and oil it occasionally. N690 will spot if you leave saltwater on it, but it will not rust through the night the way D2 can. Sharpen at 15-17 degrees per side, strop weekly, and it will last years.

If you want to compare it in hand, the Koala series also runs N690 at a smaller size, and the Trivisa range gives you plenty of blade shapes to try it in.

Should You Buy It

Yes, if you want a dependable stainless that sharpens easily and holds an edge long enough for real work. No, if you need maximum edge retention for abrasive materials or you want the latest powder metallurgy steel. N690 is not exciting. It is just reliable, and that is worth something.

N690 vs Powder Metallurgy Steels

Compared with M390 or MagnaCut, N690 gives up measurable edge retention. What it gains is sharpenability and toughness. If you sharpen your own knives and do not want to buy diamond plates, N690 is a friendlier steel. If you want to go months between sharpenings, powder metallurgy is worth the extra money.

There is no wrong answer here. Most people overestimate how much edge retention they need and underestimate how much they value a steel they can touch up in two minutes.

Leave a comment

Featured collection

View all
NewSave 15%
Bestech Wet Nellie BT2505F, open knife beside the same model folded closed, both blade profile and handle scales on a pure white studioBestech Wet Nellie BT2505F, three-quarter front view of the open knife showing the blade finish, edge bevel and spine in full